Windows 2000 Replacing the c: drive

  • Thread starter Thread starter Ray K
  • Start date Start date
R

Ray K

Due to the various problems described in my post of a few minutes ago, I'm
ready to replace my c: drive.

My system consists of a primary master drive partitioned as C, E and F, and
a primary slave drive partitioned as D and G. My plan is to remove both
these drives and install a new primary master, again partitioned as C, E,
and F. Once I reinstall w2k and sp4, I'll put the old C/E/F drive in the
primary slave position and copy the data from the E and F partitions onto
the new E and F partitions. (There are no programs on the E and F
partitions just data I've created.) Then I'll reinstall all my programs on
the new C drive and wherever possible copy their various settings from the
corresponding folder locations on the old drive to the new one.

(I realize that with the old drive moved to the slave position, the old C
partition will become D, the old E will become G, and the old F will become
H.)

Once I'm done with this, I'll remove the old C/E/F drive and replace it
with the old primary slave D and G.

As an alternative, I could disconnect one of the two cd burners in the
secondary channel and put the old C/E/F drive there that way I don't have
to remove the D/G drive from its primary slave position.

Any ideas for simplifying this nightmare?

Many thanks,

Ray
 
You might review this one.

http://support.microsoft.com/kb/234048



--

Regards,

Dave Patrick ....Please no email replies - reply in newsgroup.
Microsoft Certified Professional
Microsoft MVP [Windows]
http://www.microsoft.com/protect

"Ray K" wrote:
> Due to the various problems described in my post of a few minutes ago, I'm
> ready to replace my c: drive.
>
> My system consists of a primary master drive partitioned as C, E and F,
> and
> a primary slave drive partitioned as D and G. My plan is to remove both
> these drives and install a new primary master, again partitioned as C, E,
> and F. Once I reinstall w2k and sp4, I'll put the old C/E/F drive in the
> primary slave position and copy the data from the E and F partitions onto
> the new E and F partitions. (There are no programs on the E and F
> partitions just data I've created.) Then I'll reinstall all my programs
> on
> the new C drive and wherever possible copy their various settings from
> the
> corresponding folder locations on the old drive to the new one.
>
> (I realize that with the old drive moved to the slave position, the old C
> partition will become D, the old E will become G, and the old F will
> become
> H.)
>
> Once I'm done with this, I'll remove the old C/E/F drive and replace it
> with the old primary slave D and G.
>
> As an alternative, I could disconnect one of the two cd burners in the
> secondary channel and put the old C/E/F drive there that way I don't have
> to remove the D/G drive from its primary slave position.
>
> Any ideas for simplifying this nightmare?
>
> Many thanks,
>
> Ray
>
>
>
 
Why not simply delete the partition & clean install on your origonal C ?
You may have problems with the drive letter, as your current drive
designations seem a little odd

"Ray K" <raykosXXX@optonline.net> wrote in message
news:47c77c76$0$29422$607ed4bc@cv.net...
> Due to the various problems described in my post of a few minutes ago, I'm
> ready to replace my c: drive.
>
> My system consists of a primary master drive partitioned as C, E and F,
> and
> a primary slave drive partitioned as D and G. My plan is to remove both
> these drives and install a new primary master, again partitioned as C, E,
> and F. Once I reinstall w2k and sp4, I'll put the old C/E/F drive in the
> primary slave position and copy the data from the E and F partitions onto
> the new E and F partitions. (There are no programs on the E and F
> partitions just data I've created.) Then I'll reinstall all my programs
> on
> the new C drive and wherever possible copy their various settings from
> the
> corresponding folder locations on the old drive to the new one.
>
> (I realize that with the old drive moved to the slave position, the old C
> partition will become D, the old E will become G, and the old F will
> become
> H.)
>
> Once I'm done with this, I'll remove the old C/E/F drive and replace it
> with the old primary slave D and G.
>
> As an alternative, I could disconnect one of the two cd burners in the
> secondary channel and put the old C/E/F drive there that way I don't have
> to remove the D/G drive from its primary slave position.
>
> Any ideas for simplifying this nightmare?
>
> Many thanks,
>
> Ray
>
>
>
 
"DL" <address@invalid> wrote in message
news:ul18AuqeIHA.2000@TK2MSFTNGP03.phx.gbl...
> Why not simply delete the partition & clean install on your origonal C ?

Won't that destroy the data I've saved on the drive? I haven't been able to
save that data because I can't boot. Besides, how do I delete the partition
if I can't boot? (Perhaps one of the dos programs, like fdisk, that I could
run from the floppy.)


> You may have problems with the drive letter, as your current drive
> designations seem a little odd
>
> "Ray K" <raykosXXX@optonline.net> wrote in message
> news:47c77c76$0$29422$607ed4bc@cv.net...
> > Due to the various problems described in my post of a few minutes ago,
I'm
> > ready to replace my c: drive.
> >
> > My system consists of a primary master drive partitioned as C, E and F,
> > and
> > a primary slave drive partitioned as D and G. My plan is to remove both
> > these drives and install a new primary master, again partitioned as C,
E,
> > and F. Once I reinstall w2k and sp4, I'll put the old C/E/F drive in the
> > primary slave position and copy the data from the E and F partitions
onto
> > the new E and F partitions. (There are no programs on the E and F
> > partitions just data I've created.) Then I'll reinstall all my programs
> > on
> > the new C drive and wherever possible copy their various settings from
> > the
> > corresponding folder locations on the old drive to the new one.
> >
> > (I realize that with the old drive moved to the slave position, the old
C
> > partition will become D, the old E will become G, and the old F will
> > become
> > H.)
> >
> > Once I'm done with this, I'll remove the old C/E/F drive and replace it
> > with the old primary slave D and G.
> >
> > As an alternative, I could disconnect one of the two cd burners in the
> > secondary channel and put the old C/E/F drive there that way I don't
have
> > to remove the D/G drive from its primary slave position.
> >
> > Any ideas for simplifying this nightmare?
> >
> > Many thanks,
> >
> > Ray
> >
> >
> >
>
>
 
Only on the C partition & I believe you said data was on other parttions,
besides which if C is infected you may 'recover' any infection if you copy
files from C to elsewhere

"Ray K" <raykosXXX@optonline.net> wrote in message
news:47c81a0c$0$29453$607ed4bc@cv.net...
>
> "DL" <address@invalid> wrote in message
> news:ul18AuqeIHA.2000@TK2MSFTNGP03.phx.gbl...
>> Why not simply delete the partition & clean install on your origonal C ?
>
> Won't that destroy the data I've saved on the drive? I haven't been able
> to
> save that data because I can't boot. Besides, how do I delete the
> partition
> if I can't boot? (Perhaps one of the dos programs, like fdisk, that I
> could
> run from the floppy.)
>
>
>> You may have problems with the drive letter, as your current drive
>> designations seem a little odd
>>
>> "Ray K" <raykosXXX@optonline.net> wrote in message
>> news:47c77c76$0$29422$607ed4bc@cv.net...
>> > Due to the various problems described in my post of a few minutes ago,
> I'm
>> > ready to replace my c: drive.
>> >
>> > My system consists of a primary master drive partitioned as C, E and F,
>> > and
>> > a primary slave drive partitioned as D and G. My plan is to remove both
>> > these drives and install a new primary master, again partitioned as C,
> E,
>> > and F. Once I reinstall w2k and sp4, I'll put the old C/E/F drive in
>> > the
>> > primary slave position and copy the data from the E and F partitions
> onto
>> > the new E and F partitions. (There are no programs on the E and F
>> > partitions just data I've created.) Then I'll reinstall all my
>> > programs
>> > on
>> > the new C drive and wherever possible copy their various settings from
>> > the
>> > corresponding folder locations on the old drive to the new one.
>> >
>> > (I realize that with the old drive moved to the slave position, the old
> C
>> > partition will become D, the old E will become G, and the old F will
>> > become
>> > H.)
>> >
>> > Once I'm done with this, I'll remove the old C/E/F drive and replace it
>> > with the old primary slave D and G.
>> >
>> > As an alternative, I could disconnect one of the two cd burners in the
>> > secondary channel and put the old C/E/F drive there that way I don't
> have
>> > to remove the D/G drive from its primary slave position.
>> >
>> > Any ideas for simplifying this nightmare?
>> >
>> > Many thanks,
>> >
>> > Ray
>> >
>> >
>> >
>>
>>
>
>
 
"DL" <address@invalid> wrote in message
news:eJAO4CveIHA.4476@TK2MSFTNGP06.phx.gbl...
> Only on the C partition & I believe you said data was on other parttions,
> besides which if C is infected you may 'recover' any infection if you copy
> files from C to elsewhere
>

The data that I want to preserve are mainly these file types: jpg, doc,
browser address book, bookmarks, emails (they are all in a single slt
SeaMonkey/Netsecape file). A couple of Excel and Access files that I created
are saved on C. I think these files are safe.I haven't imported any macros
(or created any of my own).

My plan is to make a backup image of the problem C to another partition or
drive, and then after reinstalling W2K Pro, copy just the above file types
back.

The challenge is being able to boot to the dos prompt. Can't get there even
if I select Safe Mode with DOS prompt. The resulting screen is black with
just the words Safe Mode in the four corners.

Whoops, during the six or minutes it's taken to write this, I just got the
prompt. Ran chkdsk on all five partitions on both drives. No bad sectors or
other problems.

It turns out that G has 83GB available, and C uses only about 21GB for
everything. So I'll just make a folder on G, call it C Backup, and use Xcopy
to copy everything from C to C Backup. Then I can format c: and reinstall
W2K. No need to remove one drive, or create partitions and later delete
them. Sound OK?

Thanks,

Ray


> "Ray K" <raykosXXX@optonline.net> wrote in message
> news:47c81a0c$0$29453$607ed4bc@cv.net...
> >
> > "DL" <address@invalid> wrote in message
> > news:ul18AuqeIHA.2000@TK2MSFTNGP03.phx.gbl...
> >> Why not simply delete the partition & clean install on your origonal C
?
> >
> > Won't that destroy the data I've saved on the drive? I haven't been able
> > to
> > save that data because I can't boot. Besides, how do I delete the
> > partition
> > if I can't boot? (Perhaps one of the dos programs, like fdisk, that I
> > could
> > run from the floppy.)
> >
> >
> >> You may have problems with the drive letter, as your current drive
> >> designations seem a little odd
> >>
> >> "Ray K" <raykosXXX@optonline.net> wrote in message
> >> news:47c77c76$0$29422$607ed4bc@cv.net...
> >> > Due to the various problems described in my post of a few minutes
ago,
> > I'm
> >> > ready to replace my c: drive.
> >> >
> >> > My system consists of a primary master drive partitioned as C, E and
F,
> >> > and
> >> > a primary slave drive partitioned as D and G. My plan is to remove
both
> >> > these drives and install a new primary master, again partitioned as
C,
> > E,
> >> > and F. Once I reinstall w2k and sp4, I'll put the old C/E/F drive in
> >> > the
> >> > primary slave position and copy the data from the E and F partitions
> > onto
> >> > the new E and F partitions. (There are no programs on the E and F
> >> > partitions just data I've created.) Then I'll reinstall all my
> >> > programs
> >> > on
> >> > the new C drive and wherever possible copy their various settings
from
> >> > the
> >> > corresponding folder locations on the old drive to the new one.
> >> >
> >> > (I realize that with the old drive moved to the slave position, the
old
> > C
> >> > partition will become D, the old E will become G, and the old F will
> >> > become
> >> > H.)
> >> >
> >> > Once I'm done with this, I'll remove the old C/E/F drive and replace
it
> >> > with the old primary slave D and G.
> >> >
> >> > As an alternative, I could disconnect one of the two cd burners in
the
> >> > secondary channel and put the old C/E/F drive there that way I don't
> > have
> >> > to remove the D/G drive from its primary slave position.
> >> >
> >> > Any ideas for simplifying this nightmare?
> >> >
> >> > Many thanks,
> >> >
> >> > Ray
> >> >
> >> >
> >> >
> >>
> >>
> >
> >
>
>
 
When using Xcopy, I'll use the /E switch to copy subfolders, even empty ones
(although maybe I better off using /S and not copying the empty ones), and
the /K switch to copy attributes. I won't use /H because that would copy
hidden and system files also, which I assume will be reloaded during
reinstall.

Ray
 
sounds about right

"Ray K" <raykosXXX@optonline.net> wrote in message
news:47c8531d$0$29438$607ed4bc@cv.net...
>
> "DL" <address@invalid> wrote in message
> news:eJAO4CveIHA.4476@TK2MSFTNGP06.phx.gbl...
>> Only on the C partition & I believe you said data was on other parttions,
>> besides which if C is infected you may 'recover' any infection if you
>> copy
>> files from C to elsewhere
>>
>
> The data that I want to preserve are mainly these file types: jpg, doc,
> browser address book, bookmarks, emails (they are all in a single slt
> SeaMonkey/Netsecape file). A couple of Excel and Access files that I
> created
> are saved on C. I think these files are safe.I haven't imported any macros
> (or created any of my own).
>
> My plan is to make a backup image of the problem C to another partition or
> drive, and then after reinstalling W2K Pro, copy just the above file types
> back.
>
> The challenge is being able to boot to the dos prompt. Can't get there
> even
> if I select Safe Mode with DOS prompt. The resulting screen is black with
> just the words Safe Mode in the four corners.
>
> Whoops, during the six or minutes it's taken to write this, I just got the
> prompt. Ran chkdsk on all five partitions on both drives. No bad sectors
> or
> other problems.
>
> It turns out that G has 83GB available, and C uses only about 21GB for
> everything. So I'll just make a folder on G, call it C Backup, and use
> Xcopy
> to copy everything from C to C Backup. Then I can format c: and reinstall
> W2K. No need to remove one drive, or create partitions and later delete
> them. Sound OK?
>
> Thanks,
>
> Ray
>
>
>> "Ray K" <raykosXXX@optonline.net> wrote in message
>> news:47c81a0c$0$29453$607ed4bc@cv.net...
>> >
>> > "DL" <address@invalid> wrote in message
>> > news:ul18AuqeIHA.2000@TK2MSFTNGP03.phx.gbl...
>> >> Why not simply delete the partition & clean install on your origonal C
> ?
>> >
>> > Won't that destroy the data I've saved on the drive? I haven't been
>> > able
>> > to
>> > save that data because I can't boot. Besides, how do I delete the
>> > partition
>> > if I can't boot? (Perhaps one of the dos programs, like fdisk, that I
>> > could
>> > run from the floppy.)
>> >
>> >
>> >> You may have problems with the drive letter, as your current drive
>> >> designations seem a little odd
>> >>
>> >> "Ray K" <raykosXXX@optonline.net> wrote in message
>> >> news:47c77c76$0$29422$607ed4bc@cv.net...
>> >> > Due to the various problems described in my post of a few minutes
> ago,
>> > I'm
>> >> > ready to replace my c: drive.
>> >> >
>> >> > My system consists of a primary master drive partitioned as C, E and
> F,
>> >> > and
>> >> > a primary slave drive partitioned as D and G. My plan is to remove
> both
>> >> > these drives and install a new primary master, again partitioned as
> C,
>> > E,
>> >> > and F. Once I reinstall w2k and sp4, I'll put the old C/E/F drive in
>> >> > the
>> >> > primary slave position and copy the data from the E and F partitions
>> > onto
>> >> > the new E and F partitions. (There are no programs on the E and F
>> >> > partitions just data I've created.) Then I'll reinstall all my
>> >> > programs
>> >> > on
>> >> > the new C drive and wherever possible copy their various settings
> from
>> >> > the
>> >> > corresponding folder locations on the old drive to the new one.
>> >> >
>> >> > (I realize that with the old drive moved to the slave position, the
> old
>> > C
>> >> > partition will become D, the old E will become G, and the old F will
>> >> > become
>> >> > H.)
>> >> >
>> >> > Once I'm done with this, I'll remove the old C/E/F drive and replace
> it
>> >> > with the old primary slave D and G.
>> >> >
>> >> > As an alternative, I could disconnect one of the two cd burners in
> the
>> >> > secondary channel and put the old C/E/F drive there that way I
>> >> > don't
>> > have
>> >> > to remove the D/G drive from its primary slave position.
>> >> >
>> >> > Any ideas for simplifying this nightmare?
>> >> >
>> >> > Many thanks,
>> >> >
>> >> > Ray
>> >> >
>> >> >
>> >> >
>> >>
>> >>
>> >
>> >
>>
>>
>
>
 
Thanks for the prompt reply. I'm off and running with the copying.

Ray

"DL" <address@invalid> wrote in message
news:u2tLvcweIHA.4120@TK2MSFTNGP06.phx.gbl...
> sounds about right
>
> "Ray K" <raykosXXX@optonline.net> wrote in message
> news:47c8531d$0$29438$607ed4bc@cv.net...
> >
> > "DL" <address@invalid> wrote in message
> > news:eJAO4CveIHA.4476@TK2MSFTNGP06.phx.gbl...
> >> Only on the C partition & I believe you said data was on other
parttions,
> >> besides which if C is infected you may 'recover' any infection if you
> >> copy
> >> files from C to elsewhere
> >>
> >
> > The data that I want to preserve are mainly these file types: jpg, doc,
> > browser address book, bookmarks, emails (they are all in a single slt
> > SeaMonkey/Netsecape file). A couple of Excel and Access files that I
> > created
> > are saved on C. I think these files are safe.I haven't imported any
macros
> > (or created any of my own).
> >
> > My plan is to make a backup image of the problem C to another partition
or
> > drive, and then after reinstalling W2K Pro, copy just the above file
types
> > back.
> >
> > The challenge is being able to boot to the dos prompt. Can't get there
> > even
> > if I select Safe Mode with DOS prompt. The resulting screen is black
with
> > just the words Safe Mode in the four corners.
> >
> > Whoops, during the six or minutes it's taken to write this, I just got
the
> > prompt. Ran chkdsk on all five partitions on both drives. No bad sectors
> > or
> > other problems.
> >
> > It turns out that G has 83GB available, and C uses only about 21GB for
> > everything. So I'll just make a folder on G, call it C Backup, and use
> > Xcopy
> > to copy everything from C to C Backup. Then I can format c: and
reinstall
> > W2K. No need to remove one drive, or create partitions and later delete
> > them. Sound OK?
> >
> > Thanks,
> >
> > Ray
> >
> >
> >> "Ray K" <raykosXXX@optonline.net> wrote in message
> >> news:47c81a0c$0$29453$607ed4bc@cv.net...
> >> >
> >> > "DL" <address@invalid> wrote in message
> >> > news:ul18AuqeIHA.2000@TK2MSFTNGP03.phx.gbl...
> >> >> Why not simply delete the partition & clean install on your origonal
C
> > ?
> >> >
> >> > Won't that destroy the data I've saved on the drive? I haven't been
> >> > able
> >> > to
> >> > save that data because I can't boot. Besides, how do I delete the
> >> > partition
> >> > if I can't boot? (Perhaps one of the dos programs, like fdisk, that I
> >> > could
> >> > run from the floppy.)
> >> >
> >> >
> >> >> You may have problems with the drive letter, as your current drive
> >> >> designations seem a little odd
> >> >>
> >> >> "Ray K" <raykosXXX@optonline.net> wrote in message
> >> >> news:47c77c76$0$29422$607ed4bc@cv.net...
> >> >> > Due to the various problems described in my post of a few minutes
> > ago,
> >> > I'm
> >> >> > ready to replace my c: drive.
> >> >> >
> >> >> > My system consists of a primary master drive partitioned as C, E
and
> > F,
> >> >> > and
> >> >> > a primary slave drive partitioned as D and G. My plan is to remove
> > both
> >> >> > these drives and install a new primary master, again partitioned
as
> > C,
> >> > E,
> >> >> > and F. Once I reinstall w2k and sp4, I'll put the old C/E/F drive
in
> >> >> > the
> >> >> > primary slave position and copy the data from the E and F
partitions
> >> > onto
> >> >> > the new E and F partitions. (There are no programs on the E and F
> >> >> > partitions just data I've created.) Then I'll reinstall all my
> >> >> > programs
> >> >> > on
> >> >> > the new C drive and wherever possible copy their various settings
> > from
> >> >> > the
> >> >> > corresponding folder locations on the old drive to the new one.
> >> >> >
> >> >> > (I realize that with the old drive moved to the slave position,
the
> > old
> >> > C
> >> >> > partition will become D, the old E will become G, and the old F
will
> >> >> > become
> >> >> > H.)
> >> >> >
> >> >> > Once I'm done with this, I'll remove the old C/E/F drive and
replace
> > it
> >> >> > with the old primary slave D and G.
> >> >> >
> >> >> > As an alternative, I could disconnect one of the two cd burners in
> > the
> >> >> > secondary channel and put the old C/E/F drive there that way I
> >> >> > don't
> >> > have
> >> >> > to remove the D/G drive from its primary slave position.
> >> >> >
> >> >> > Any ideas for simplifying this nightmare?
> >> >> >
> >> >> > Many thanks,
> >> >> >
> >> >> > Ray
> >> >> >
> >> >> >
> >> >> >
> >> >>
> >> >>
> >> >
> >> >
> >>
> >>
> >
> >
>
>
 
Back
Top