PCI SATA Card

  • Thread starter Thread starter Edward W. Thompson
  • Start date Start date
E

Edward W. Thompson

My motherboard has two SATA ports both of which feed HDDs. I needed
additional capacity and as I intend at some stage to 'upgrade' I bought
(ebay) a new SATA drive (320GB Seagate formatted NTFS)) and a PCI SATA Card
(Via chipset) to give me additional SATA ports. The PCI SATA Card came
with the requisite drivers (at least I think so!) but no 'how to guide'.

I installed the HDD and card and loaded the card drivers. At the POST the
'new' HDD did not show but it did show after WINXP started in Disk
Management as Drive 2 with a letter designator (L). The disk was shown as
formatted NTFS as a primary drive. As the HDD is 320GB I wished to
partition it and it is at this point I ran into a problem as I couldn't
access the disk to delete the existing partition to allow me to repartition.

I tried various 'partitioning software' including the WINXP install disk
none of which could see the new drive as clearly the necessary drivers for
the PCI Card were not being accessed. To cut the story short, I
disconnected HDD drive 1 and connected the new HDD in its place. This then
allowed me to access the new drive through Disk Management to delete the
existing primary partition and create the required extended and logical
partitions. I then reconnected all HDDs and everything is now working OK.

As an aside, during this 'episode' I started to get the message 'Disk D:
needs checking for consistency' at boot up. Why, I have no idea, but
running 'fsutil dirty query D:' gave 'dirty' which 'chkdsk d: /f/x' seems to
have fixed.

Other than hoping my experience may help someone, can anyone tell me if
there is another/better method to repartition a SATA drive connected to a
PCI SATA Card.
 
Did you check to see if the PCI card showed up properly in Device Manager?

JS

"Edward W. Thompson" <thomeduk1@btopenworld.com> wrote in message
news:um6lvRr$HHA.1212@TK2MSFTNGP05.phx.gbl...
> My motherboard has two SATA ports both of which feed HDDs. I needed
> additional capacity and as I intend at some stage to 'upgrade' I bought
> (ebay) a new SATA drive (320GB Seagate formatted NTFS)) and a PCI SATA
> Card (Via chipset) to give me additional SATA ports. The PCI SATA Card
> came with the requisite drivers (at least I think so!) but no 'how to
> guide'.
>
> I installed the HDD and card and loaded the card drivers. At the POST the
> 'new' HDD did not show but it did show after WINXP started in Disk
> Management as Drive 2 with a letter designator (L). The disk was shown as
> formatted NTFS as a primary drive. As the HDD is 320GB I wished to
> partition it and it is at this point I ran into a problem as I couldn't
> access the disk to delete the existing partition to allow me to
> repartition.
>
> I tried various 'partitioning software' including the WINXP install disk
> none of which could see the new drive as clearly the necessary drivers for
> the PCI Card were not being accessed. To cut the story short, I
> disconnected HDD drive 1 and connected the new HDD in its place. This
> then allowed me to access the new drive through Disk Management to delete
> the existing primary partition and create the required extended and
> logical partitions. I then reconnected all HDDs and everything is now
> working OK.
>
> As an aside, during this 'episode' I started to get the message 'Disk D:
> needs checking for consistency' at boot up. Why, I have no idea, but
> running 'fsutil dirty query D:' gave 'dirty' which 'chkdsk d: /f/x' seems
> to have fixed.
>
> Other than hoping my experience may help someone, can anyone tell me if
> there is another/better method to repartition a SATA drive connected to a
> PCI SATA Card.
>
 
It depends entirely on the PCI sata card and whether the card has a bootable
bios of its own ie seperate from the PC Bios


"Edward W. Thompson" <thomeduk1@btopenworld.com> wrote in message
news:um6lvRr$HHA.1212@TK2MSFTNGP05.phx.gbl...
> My motherboard has two SATA ports both of which feed HDDs. I needed
> additional capacity and as I intend at some stage to 'upgrade' I bought
> (ebay) a new SATA drive (320GB Seagate formatted NTFS)) and a PCI SATA
> Card (Via chipset) to give me additional SATA ports. The PCI SATA Card
> came with the requisite drivers (at least I think so!) but no 'how to
> guide'.
>
> I installed the HDD and card and loaded the card drivers. At the POST the
> 'new' HDD did not show but it did show after WINXP started in Disk
> Management as Drive 2 with a letter designator (L). The disk was shown as
> formatted NTFS as a primary drive. As the HDD is 320GB I wished to
> partition it and it is at this point I ran into a problem as I couldn't
> access the disk to delete the existing partition to allow me to
> repartition.
>
> I tried various 'partitioning software' including the WINXP install disk
> none of which could see the new drive as clearly the necessary drivers for
> the PCI Card were not being accessed. To cut the story short, I
> disconnected HDD drive 1 and connected the new HDD in its place. This
> then allowed me to access the new drive through Disk Management to delete
> the existing primary partition and create the required extended and
> logical partitions. I then reconnected all HDDs and everything is now
> working OK.
>
> As an aside, during this 'episode' I started to get the message 'Disk D:
> needs checking for consistency' at boot up. Why, I have no idea, but
> running 'fsutil dirty query D:' gave 'dirty' which 'chkdsk d: /f/x' seems
> to have fixed.
>
> Other than hoping my experience may help someone, can anyone tell me if
> there is another/better method to repartition a SATA drive connected to a
> PCI SATA Card.
>
 
Back
Top